In a family set up with few members or temporary residences, a portable dishwasher is enough to get your dishes sparkling and hygienic. It is designed with a smaller interior space thus accommodating fewer dishes contrasted to the larger fixed dishwashers.
A pull-out faucet comes handy when you have a portable dishwasher enabling you to have your dishes well rinsed after washing. The knowledge on how to hook up the two when cleaning your dishes will facilitate smooth operations in your kitchen.
Benefits of Using a Pull-out Faucet
A pull-out faucet is more beneficial in a kitchen setup where the space is limited especially around the sink. Its ability to function effectively in a limited space makes it suitable for a portable dishwasher. In addition, the pull-out faucets will occupy less headroom space than the pull-down models.
This implies that such faucets can be used in kitchens where cabinets are installed above the sink with little inconvenience. In case of a leak, one can easily rectify the leak by checking the connections around the hose and taking the necessary corrective measure.
Why have a Portable Dishwasher?
The key benefit that comes with a portable dishwasher is flexibility and the ability to perform well in any kitchen layout. In the event whereby your floor space is limited, a portable dishwasher will serve you right.
In addition, the portable dishwasher will work with any plumbing setup, unlike the built-in dishwashers that require properly installed plumbing systems.
You will also notice its effectiveness to clean your dishes removing all stains, dirt and leaving them sparkling clean. The risk associated with breakages during cleaning is low with portable dishwashers since the load on the machine is in small manageable quantities.
Water wastage is cut short when you opt for a portable dishwasher instead of hand dish-washing where a lot of water is used.
Hooking up your Portable Dishwasher to a Pull out Faucet
One limitation of the portable dishwasher is that you cannot run both the kitchen faucet and the dishwasher simultaneously due to limited access to the sink.
However, you can counter this limitation by linking the two through a simple DIY procedure at home. This step-by-step procedure will save you time and money and make your experience with the portable dishwasher commendable.
- Unscrew the aerator
An aerator is connected to your pull-out faucet to add air to the water flowing from the faucet. You, therefore, begin by disconnecting the faucet from the aerator. You will be able to unscrew the aerator from your faucet through the use of your hands.
Simply hold the faucet spout with one hand and loosen the aerator using the other hand. Keep the aerator safe because you will need it later.
- Connect the Portable Faucet Aerator and Adapter
Once the faucet aerator is separated from the faucet spout, the next step is to link the faucet aerator of the portable dishwasher to the extended adaptor. The dishwasher faucet aerator is customized to function with extension adaptors.
Using a powered screwdriver, connect the two tightly as this will prevent water leaks when the dishwasher is in use. This step is crucial therefore take your time to countercheck the connections to identify any loose ends.
- Check for Leaks and Gaps in the connections
The essence of having a portable dishwasher is to ensure effective cleaning with minimal water. However, if leaks occur during the connections, this purpose is not met as much water is lost.
It is thus necessary to check for any leaks in the connection and any misfit between the aerator and the adapter. Misfits need to be replaced immediately before the dishwasher is put into use. Damaged parts must be replaced as well at this stage for an effective system.
- Place your Portable Dishwasher
At this stage you are doing temporary mounting therefore you need to check the surface beside your kitchen sink to ensure it is safe to place your portable dishwasher. Once you locate the storage compartment beneath your sink and remove the water hose, slide your dishwasher in place.
Align the dishwasher hose collar with the adapter for the best fit. Gradually, push the collar ring downwards into the faucet aerator. Your portable dishwasher is almost set for use.
- Join the Hose
Immediately you finish connecting the special aerator to the adapter; connect the hose to the dishwasher. Make sure the hose is attached to the sink and connected to the special faucet adapter of the portable dishwasher. Again, you must ensure there are no leaks while connecting the hose.
- Check the water pressure
Finally, it is time to check how well your hook-up of the portable dishwasher to the pull-out faucet is. Simply test this by turning on hot water which comes with high pressure.
This pressure helps in detecting any leaks or blockages in your connections allowing you to correct any errors in the connection. Your portable dishwasher is ready for use!
Similar Post You May Like: How to Remove Flow Restrictor from Kitchen Faucet
How to Maintain Portable Dishwasher
A quality portable dishwasher should serve you for an average 10 to 12 years. This is nevertheless dependent on how well you maintain your dishwasher. It is important to do some routine maintenance of your portable dishwasher and pull-out faucet to make it durable and functional.
Such would include emptying the dishwasher once it is done cleaning your dishes, washing it after use, inspecting and cleaning the spinning arms, cleaning the edges and exteriors, unclogging and cleaning the drain, using acid to remove any build-up materials, and eventually getting rid of mildew.
Conclusion
The workflow is a critical aspect in any kitchen set up meaning any available space is valuable. Having a portable dishwasher in your kitchen is one way to maximize this available space since they occupy little space.
Once connected to the pull-out faucet, its effectiveness is as great as that of a built-in dishwasher. The hook-up procedure is DIY and within minutes you can mount your dishwasher anywhere for better cleaning of your dishes.