Removing a Delta shower handle with no set screw can be tricky. But do not worry. This guide will help you. We will go step-by-step. You do not need to be a plumber. Just follow these simple instructions.
Tools Needed
You will need a few tools. Here is a list:
- Flathead screwdriver
- Phillips screwdriver
- Allen wrench
- Needle-nose pliers
- Old cloth
Gather these tools before starting. It will make the job easier.
Step 1: Turn Off Water Supply
First, turn off the water supply. This step is important. You do not want water to spray everywhere. You can find the water valve near the shower. Turn it off.
Step 2: Cover the Drain
Next, cover the drain with an old cloth. Small parts can fall. The cloth will catch them. This will save you from losing any parts.
Step 3: Find the Handle Cap
Look at the shower handle closely. You will see a small cap. It is usually in the center. This cap hides the screw.
Credit: www.youtube.com
Step 4: Remove the Handle Cap
Use the flathead screwdriver. Gently pry off the cap. Be careful not to scratch the handle. Once the cap is off, you will see the screw.
Step 5: Unscrew the Handle
Use the Phillips screwdriver or Allen wrench. Unscrew the handle. Turn it counter-clockwise. Keep turning until the handle is loose.
Step 6: Pull Off the Handle
Gently pull the handle off. If it is stuck, wiggle it a bit. Do not use too much force. The handle should come off easily.
Step 7: Remove the Trim Plate
There is a trim plate behind the handle. It is usually fixed with screws. Use the Phillips screwdriver to remove them. Once the screws are out, pull off the trim plate.
Step 8: Check for Hidden Screws
Sometimes, there might be hidden screws. Check behind the trim plate. If you find any, use the screwdriver to remove them.
Step 9: Remove the Cartridge
The cartridge controls the water flow. It is inside the valve. Use the needle-nose pliers to pull it out. Be gentle. Do not damage the cartridge.
Step 10: Inspect the Parts
Check all the parts you removed. Look for any damage. If any part is broken, replace it. You can find replacement parts at a hardware store.
Reassembling the Handle
Once you have inspected the parts, you can reassemble the handle. Here is how:
- Place the cartridge back in the valve.
- Reattach the trim plate. Use the screws to fix it in place.
- Slide the handle back onto the valve stem.
- Secure the handle with the screw. Use the Phillips screwdriver or Allen wrench.
- Snap the handle cap back in place.
Step 11: Turn On the Water Supply
Finally, turn the water supply back on. Check if the handle works properly. Turn it on and off to test. Make sure there are no leaks.
Credit: diy.stackexchange.com
Tips for Success
Here are some tips to help you:
- Take your time. Do not rush.
- If you are unsure, ask for help.
- Keep all parts in a safe place. Do not lose any.
- Use the right tools. This makes the job easier.
When to Call a Professional
Sometimes, DIY is not enough. If you face any issues, call a professional. Here are some signs you need help:
- You cannot remove the handle.
- There is a leak you cannot fix.
- You do not have the right tools.
Plumbers have the experience. They can fix the problem quickly. It is better to be safe than sorry.
Frequently Asked Questions
How Do You Remove A Delta Shower Handle Without A Set Screw?
Check for hidden caps or covers. Pry them off to reveal screws underneath.
What Tools Do I Need To Remove A Shower Handle?
Use a flathead screwdriver, Allen wrench, and a wrench. Simple tools only.
Can I Remove A Delta Shower Handle Myself?
Yes, it’s a simple task. Basic tools and patience are needed.
Why Can’t I See A Set Screw On My Shower Handle?
Some models hide screws under decorative caps. Remove the cap to find it.
Conclusion
Removing a Delta shower handle with no set screw is not hard. Just follow these steps. Use the right tools. Take your time. You can do it. If you need help, do not hesitate to call a professional.
We hope this guide was helpful. Good luck with your project!
Leave a Reply